- #Chirp usb driver windows 10 how to
- #Chirp usb driver windows 10 64 Bit
- #Chirp usb driver windows 10 serial
- #Chirp usb driver windows 10 windows 10
- #Chirp usb driver windows 10 Pc
#Chirp usb driver windows 10 64 Bit
What you will need to know is if your dad's computer is running off of 32 bit or 64 bit software.
#Chirp usb driver windows 10 windows 10
*Includes the following version of of the Windows operating system: Windows 7, Windows Server 2008 R2 and Windows 8, 8.1, Windows server 2012 R2, Windows Server 2016 and Windows 10 They only have one driver installation for Windows, and although I am using Windows 10 and you asked for Windows 7, they have this note: I solved it by going directly to the Baofeng website driver page.
#Chirp usb driver windows 10 how to
software drivers) that tell the hardware (the USB port) how to do that. What your computer is doing is emulating an analog COM port through the USB cable, and it has to have special instructions (i.e. The issue is that it's not really a USB cable per say. Not sure which version of CHIRP you are using.I know this is an old question, but I recently had to setup Chirp again on a new computer and have long since lost the driver CD that came with my cable. om the CHIRP website list of supported radios."For Wouxun KG-UV3D use KG-UVD1P"Ĭlick "OK", then follow the instructions to download from the radio, eventually the list of memories will appear Launch CHIRP, select "Download from Radio" from the "Radio" menu, select the Port as ttyUSB0, Vendor Wouxun
#Chirp usb driver windows 10 Pc
With the radio switched off, connect the programming cable to the pc and radio.
#Chirp usb driver windows 10 serial
You are almost there, the USB to serial adapter chip is identified and the port is identified as ttyUSB0 I could imagine all types of headaches.Īlternatively I could just go through the much simpler learning of the Wouxun's interface and just load a couple memory channels through the radio's menu, which is all I'm really trying to do. This is linux and its all about learning stuff which I am always happy to try but I don't want to break any already working USB functionality to get this cable working. Do you think I need to proceed with that further stuff if I am getting "pl2303 converter now attached to ttyUSB0"? It starts to get pretty complicated (for me) in setting paths or loading other stuff. Reading the instructions in the site I wasn't able to understand where they were going with the further suggestions there. And I think I did get the cable working in windows (7 or 10? can't remember) at one point but can't get it working in a new windows installation on a different laptop recently. can't remember where I bought the cable but knowing my habits I probably researched a cable that was known to be compatible and might have paid a little extra for one. usb 1-1: pl2303 converter now attached to looks like the pl2303 is identified. usb 1-1: Manufacturer: Prolific Technology Inc. usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-1: New USB device found, idVendor=067b, idProduct=2303, bcdDevice= 3.00 usb 1-1: new full-speed USB device number 9 using xhci_hcd pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0 usb 1-1: USB disconnect, device number 8 Here's the last lines from the dmesg command:
On my FT-60 the programming cable 4-pole jack has to be precisely positioned - just a slightly different design plug can ease the connection issuesįrom your suggestion to check out site. The actual connection of the programming cable to the radio can be a source of poor comms. on this page - which makes interesting reading RXD (to radio)is on the sleeve of the 3.5 mm plug. It is a 5 Volt (TTL) serial interface, with Ground and TXD (fKrom Radio) on the sleeve and ring of the 2.5mm connector. The connection consists of a 3.5 mm and a 2.5 mm 3-conductor phone plug (TRS).
The KG-UVD1P and KG-UV2D, KG-UV3D, KG-UV6D radios use the same cable as the Kenwood TH-F6A and TH-K2A listed above. The Chirp website mentions the KG-UV3D with. There is lots of help on the Internet about checking the USB to serial connection, and the trials and tribulations of the Prolific chips often used, this is typical. USB to serial converters are notoriously "inconsistent" under Linux.
0 kommentar(er)
